Sunday, May 9, 2010

Equipment sheet metal forming

Posted by Amdani at 2:19 AM
Basic sheet forming operations involve a press, punch, or ram and a set of dies
1 Presses
Press machine takes a great deal of force and energy to cut and form sheet metal. For example, to cut a 10-in.-diameter circle out of a sheet of 0.125-in.-thick mild steel, it takes approximately 157,000 lbs. of pressure. To help put this in perspective, you would have to stack approximately 13 elephants on top of a cutting punch for it to penetrate through the sheet metal.
A press is a special machine that supplies the necessary force to form and cut the sheet metal. Consider this: One ton equals 2,000 lbs. Achieving a force equal to 157,000 lbs. requires a press with a minimum force of 78.5 tons. By today's standards, this is a very small, low-tonnage press. Presses range in tonnage from 10 to 50,000; 50,000 tons equal 100 million lbs. Press safety procedures are critical. Even the smallest press will not stop for an arm or a finger.
The numerous presses in use today can be grouped into three basic types: crank-drive, hydraulic-drive, and servo-drive. Many variations exist. Some of the most common are gap-frame, straight-side, and eyelet presses.
Some presses can run at speeds in excess of 1,500 strokes per minute. These commonly are referred to as high-speed presses. Other presses may cycle very slowly and produce fewer parts in a given amount of time. The speed at which a press cycles is based on many factors, including the sheet metal type, the shape and size of the part, the type of die that is used, as well as the type of automated equipment used in the stamping process.
All presses utilize a moving component or portion of the press called the ram. One half of the die is attached to the ram, while the other half is attached to a stationary part of the press called the bolster plate (Figure 4). The distance that the ram travels in one direction is referred to as the stroke of the press. Presses have stroke lengths from 0.250 in. to 40 in. depending on the intended application. To accommodate a large variety of die thicknesses, the press's shut height must be adjustable. The shut height can be defined as the distance from the bottom surface of the ram to the top surface of the bolster plate when the press ram is at its lowest point. We call this ram position bottom dead center.
Don't confuse the stroke length of the press with its shut height. With the exceptions of hydraulic and servo presses, the stroke length is a constant distance, while the shut height can be altered. For example, if your press has an 8-in. strokelength, the ram travels a distance of 8 in. downward and 8 in. upward for a total cycle distance of 16 in. The position in which the ram starts this motion is adjustable, but the 8 in. of travel distance or stroke length is not. The press's total shut height adjustability changes with respect to the type, size, and purpose of the press. For example, a 500-ton tryout press, typically used by die builders, may have a great deal of shut height adjustment; 10 in. to 20 in. is not uncommon. This allows the die shop to build and try out many different die types and sizes.
High-speed presses typically have short stroke lengths and, therefore, very little shut height adjustability. Using a press with an excessive stroke length can result in lower part output. This is because the ram travels an excessive distance before the die is actually performing work.
As mentioned earlier, hydraulic- and servo-drive presses are the exceptions to these basic rules. These presses have both adjustable shut heights and stroke lengths and are good candidates for a variety of stamping operations.
Great care must be taken when selecting a press. Variables such as tonnage, stroke length, bed size, deflection rates, ram speeds, drive types, and shut height adjustability are very important. However, one of the key things to remember is that the press is a very crucial part of the metal stamping process. The wrong type or a poorly maintained press may result in failure regardless of the die quality.When I am conducting a public seminar, I tell my attendees, "You can have a jewel of a die, but if you put it in a glorified 200-ton trash compactor, you will make trash." Don't dismiss the importance of the press
Type of press machine
• Mechanical Press - The ram is actuated using a flywheel. Stroke motion is not uniform.
• Hydraulic Press - Longer strokes than mechanical presses, and develop full force throughout the stroke. Stroke motion is of uniform speed, especially adapted to deep drawing operations.

3 comments:

Unknown said...

Best Hydraulic Scissor Lift Manufacturer in India. We design various types of hydraulic lift, hydraulic cylinders, hydraulic presses, Industrial hydraulic equipment etc.

Anonymous said...


Thanks for sharing such an informative blog ,the way you express your views are so easy to understand.
Contact us for:
Hydraulic Press Machine
Compressed Earth Block Machine
Hydraulic Power Press
Compact Hydraulic Cylinder
Compact Hydraulic Cylinder Manufacturers
Industrial Hydraulic Jack manufacturers
Hydraulic Lift Cylinder
Electric Hydraulic Press
Hydraulic Forging Press
Hydraulic Remote Control Jack

Woodmac Industries said...

Core Drying - Woodmac Group is provide services 1500 tons Hydraulic Press, Wooden Products Manufacturers in India, Manufacturing of Wooden Products in India, Manufacturing of Wooden Products, Hydraulic Hot Press for Plywood in India, USA, Canada, Australia, Malaysia, Peru, South Africa, Nepal, Bangladesh, Philippines, UAE, Venezuela, Egypt, Columbia, Chile, Brazil. Contact Now! 9417283898

Post a Comment

 

Copyright © 2011 Diesmtc.blogspot.com | Design by Kenga Ads-template